Aftercare for Your Ceramic Pro Protection

Simple habits that help your coating, film, and tint perform as intended. When in doubt, call the shop that installed it.

Introduction

Congratulations on protecting your vehicle with Ceramic Pro products at Next Level Ceramic. Follow the care steps below for ceramic coatings, KAVACA paint protection film, and KAVACA window tint. If your job packet or warranty paperwork says something different for the products on your vehicle, follow that paperwork.

Ceramic coatings — first two to three weeks

Give the coating time to cure (about two to three weeks, depending on weather). Do not wash the vehicle for at least two weeks after you pick it up. Limit rain, sprinklers, and other unnecessary water when you can.

During this period:

Avoid parking under trees when practical.

Clean bird droppings, bug splatter, sap, or pollen promptly with an approved detail spray and a clean microfiber towel — do not leave them for days.

If something lands on the finish and you are unsure how to remove it, contact us instead of scrubbing dry grit across the paint.

You can usually drive outdoors after about 48 hours. Keep the full wash wait at two weeks.

Ceramic coatings — ongoing care

Wash about every two weeks so dirt and fallout do not build up.

Do a thorough two-bucket hand wash about once a month.

Use a pH-appropriate ceramic aftercare soap. Avoid soaps with wax, petroleum distillates, or extreme pH. Americana Global Ceramic Aftercare products are recommended partners for Ceramic Pro systems.

Wash when panels are cool — shade, garage, early morning, or late afternoon. Do not wash hot panels in harsh sun.

Dry with dedicated microfiber drying towels (or carefully with compressed air, then finish with microfiber). Do not leave tap water to air-dry into spots.

Between washes, use an approved detail spray for light spot cleaning.

Avoid: automatic brush washes; dry-wiping grit; wax or paint sealants on the coating; ceramic “boost” sprays other than recommended options such as Ceramic Pro CARE or Americana Global Detail Spray; abrasive towels on dry paint.

If you use Ceramic Pro CARE as a drying aid, apply it on a wet surface as directed — not on dry paint.

Paint protection film (PPF)

After you take the vehicle home, avoid washing for two full days (48 hours).

Small moisture pockets or bubbles can be normal early on. Do not press or pop them. If they remain after about ten days, contact us.

Keep the film clean. Wash weekly in dusty or high-pollen conditions; every other week is fine when a ceramic coating sits on top of PPF.

Hand wash with rinseless wash or a two-bucket method and a soap suited to vinyl/PPF. Keep wheel and tire tools separate from paint tools.

Avoid automatic brush washes and high-pressure spray along film edges. Try not to leave hard water sitting on the surface.

KAVACA window tint

Tint is installed on the inside of the glass.

Keep windows raised for 3 days (72 hours) after install, or follow the specific instructions provided at pickup.

Full cure can take about one to four weeks depending on sun and heat. Mild haze, fog, streaks, or small moisture patterns can be normal — do not push trapped moisture.

Do not clean the film for at least seven days. During the first month, use light pressure, especially near edges.

Use only ammonia-free (and alcohol-free) glass cleaner with clean microfiber towels. Ammonia-based household cleaners can damage film and may affect warranty eligibility.

Ceramic Pro KAVACA window film carries a Limited Lifetime Warranty subject to Ceramic Pro’s published terms.

Maintaining warranty eligibility

Ceramic Pro coatings and KAVACA paint protection films have minimum and maximum warranty periods. Experiencing the full warranty typically requires an annual inspection/service with a certified Ceramic Pro installer.

Your written warranty paperwork for the products on your vehicle controls. Contact Next Level Ceramic during shop hours if you want help understanding what applies to your install or to ask about an inspection visit.

We’re here after install

If something looks off, if you want a maintenance recommendation, or if you would like us to look at film edges or coating behavior, contact Next Level Ceramic Monday–Friday, 9–5. Photos help us advise quickly.

5004 Bee Creek Rd, Unit 100, Spicewood, TX 78669

Monday–Friday, 9 AM–5 PM. Closed weekends.